A Beginner's Guide to Installing a Bathtub
A Beginner's Guide to Installing a Bathtub
Blog Article
The article which follows in relation to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround is exceptionally attention-grabbing. Give it a go and draw your own personal results.
Mounting a bathtub isn't exactly rocket science, however it does call for strong plumbing, woodworking, and also sometimes, tiling skills. Changing an old tub with a brand-new one is additionally a moderately tough task. If the old tub is readily available, the project can relocate immediately; if you need to open a wall surface to eliminate the old bathtub and also place the new bathtub, the task is much harder. In either situation, the task is within a house handyman's abilities, although you will require a helper to move out the old bathtub and embeded in the brand-new one. Make certain you have certified on your own for the job and also fit trying it. Instead of working with a specialist to take over a halfway-completed job, it is much better to think about employing one prior to you begin. Chances are you might require an expert plumber to make tube links.
This short article will aid you install a new tub in your shower room if you have actually currently acquired a brand-new tub as well as don't require to alter the plan of your previous water supply pipelines.
Your devices and also product list should consist of the following:
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your setup, after that the first thing you need to do is disconnect the water supply. After doing so, activate the taps to drain any type of water staying in the system. The procedure of getting rid of the existing taps can be fairly troublesome due to the restricted accessibility that is usually the case.
Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipelines to the taps. Have a towel prepared for the continuing to be water that will come from the pipes. When the supply pipelines have been removed, use the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the single faucets from turning throughout this process. When the faucets have been gotten rid of, the holes in the bath/basin will have to be cleaned up of any type of old securing compound.
Prior to proceeding to fit the new faucets, compare the pipeline links on the old taps to the new taps. If the old faucets are longer than the new faucets, after that a shank adapter is needed for the brand-new taps to fit.
Fitting New Touches
If the tails of the new faucets are plastic, then you will require a plastic connector to prevent damages to the string. One end of the port fits on the plastic tail of the faucet and also the other end offers a link to the existent supply pipelines.
If you need to fit a monobloc, then you will call for decreasing couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next, place the faucet in the installing hole in the bath/basin guaranteeing that the washing machines are in place between the tap as well as the sink. Secure the tap in place with the supplier offered backnut. When the faucet is firmly in position, the supply pipelines can be attached to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with typical faucet connectors. The previous kind needs to be attached to the faucet ends initially, tightening up just by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Installing the Bath tub
Making use of both wooden boards under its feet, place the bathtub in the required placement. The wood boards are helpful in evenly spreading out the weight of the bath tub over the area of the boards rather than focusing all the weight onto four tiny points.
The following objective is to make certain that the tub is leveled all round. This can be accomplished by inspecting the level and changing the feet on the bath tub till the spirit level checks out degree.
To mount taps, fit the bottom of the outermost adaptable tap port to the ideal supply pipeline by making a compression join; then do the very same for the various other tap.
Activate the supply of water and examine all joints and also brand-new pipework for leakages and also tighten them if needed. Fill the bath tub and additionally check the overflow outlet as well as the normal outlet for leaks.
Ultimately, deal with the bath paneling as described in the supplier's instruction manual. Tiling as well as securing around the bath tub needs to wait up until the bath tub has actually been made use of at least when as this will resolve it right into its last position.
Preparing for the Installation
Firstly, the sustaining frame provided with the bathroom should be fitted (if needed) according to the producer's guidelines. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is necessary to ensure that if the faucet features a plastic washer, it is fitted between the bath and the faucets. On a plastic bathroom, it is also practical to fit a sustaining plate under the faucets device to stop stress on the bathtub.
Fit the adaptable tap ports to the bottom of the two faucets using 2 nuts and olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet via the hole in the bathroom. Make use of the nut supplied by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make sure you make use of every one of the provided washers.
Link the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom ought to currently be ready to be suited its last placement.
Tiling Around the Tub
In the location where the bath fulfills the ceramic tile, it is required to secure the accompanies a silicone rubber caulking. This is essential as the fitting can move enough to break a rigid seal, causing the water to permeate the wall in between the bathroom and the tiling, leading to issues with moisture and possible leakages to the ceiling below.
You can pick from a variety of coloured sealers to assimilate your components as well as fittings. They are sold in tubes and also cartridges, as well as are capable of securing spaces approximately a size of 3mm (1/8 inch). If you have a bigger void to load, you can fill it with spins of soaked newspaper or soft rope. Keep in mind to always load the bathtub with water before sealing, to permit the activity experienced when the tub is in use. The sealer can split relatively very early if you do not take into consideration this movement prior to securing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are also conveniently readily available on the market. It is a good idea to fit the floor tiles making use of waterproof or waterproof adhesive and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I was shown that article about How to Install a Bathtub through a good friend on a different web blog. Be sure to take the opportunity to promote this entry if you liked it. Thank you so much for your time invested reading it.
Request expert assessment. Report this page